Skip directly to searchSkip directly to the site navigationSkip directly to the page's main content

Health Event Rates

Counts of health events are useful, but have limitations for those who need to compare populations of unequal size, for instance, a subpopulation with an overall state population. Knowing the population sizes can help to interpret counts, but computing a rate will allow direct comparison between populations of unequal size that are otherwise similar (e.g., similar age composition, similar culturally). According to the dictionary, a rate is, "a quantity, amount, or degree of something [numerator], measured per unit of something else [denominator]." In public health, the numerator is the number of people among whom an event occurred during a certain period of time, and the denominator is the total number of people in the population at risk for the same period of time. A rate has four components:
  1. A specified time period.
  2. The numerator, the number of people in whom an event occurred during a given period of time, and
  3. The denominator, the total number of people in the population at risk for the same period of time. This is also referred to as the "person-years at risk."
  4. A constant. The result of the fraction is usually multiplied by some factor of 10 (such as 100,000), so that the rate may be expressed as a whole number.

Contents
1 Crude Rates
2 Age- and Sex-Specific Rates
3 Deciding Which Measure to Use

Back to Top

Crude Rates

In general, a rate is called a "crude rate" if it has not been adjusted for the age and sex composition of a population.

Using the following values, as an example...
  1. Assume the specified time period is 2003 through 2005.
  2. Assume the numerator, or the number of events was averaged over the three years, for a value of 525.33 (before rounding).
  3. The denominator, or the estimated population at risk, was also averaged over the three years. The average of the three population estimates was 402,242.33.
  4. The constant was 100,000.

The calculation of a crude rate for the above looks like this:
info icon
info icon Many measures used in public health assessment specify a time period of one or more calendar years. This is because many public health numerator datasets have calendar year production periods. But other time periods are also commonly used; for example calendar weeks in the instance of notifiable diseases. To calculate the "person-years at risk" for a time period that is less than one year, you need to multiply the population estimate by the portion of the year represented in the numerator. For instance, to calculate a crude rate for the number of cases of disease over a 10-week period, your denominator would be the July 1 population estimate multiplied by 0.1923 (10 weeks/52 weeks).



FAQs for Crude Rates:


Combining Years

Q: I am looking at death rates for a five-year period. What should I use for a population denominator?
A: If you are combining numerator values over the five years by summing them, then use the sum of the population counts over the same period. If you are combining numerator values by taking an average, then take an average of the population counts for the same time period and geographic area. Alternatively, you could also use an average over the five years in the numerator, and a "mid-point" population estimate, that is, a population estimate for the mid-point, or middle, year in the denominator.


Back to Top


Age- and Sex-specific Rates

An age-specific rate is calculated by dividing the total number of health events for the specific age-group of interest by the total population in that age group. The calculation for an age-specific rate is the same as for a crude rate.

info icon Looking at rates within groups is also called "stratification."


info icon The crude mortality rate for a population depends on the mortality rate in each age group as well as on the proportion of people in each age group. For instance, the age-specifc rate for most causes of death will be higher for older age groups. As a result, crude death rates tend to be higher in populations with a larger proportion of older persons, and lower in populations with a larger proportion of younger persons.



Age-specific rates are valuable for comparing rates across age groups, and crude rates provide a useful summary measure to compare similar populations of different sizes. But the word, "similar" is a key concept. It can be misleading to compare crude rates across populations that have relevant differences, such as different cultural traditions, or age, sex, or race composition.

One difference that is commonly controlled for statistically is age composition of the population. The crude mortality rate for a population depends on the mortality rate in each age group as well as on the proportion of people in each age group. For instance, the age-specifc rate for most causes of death will be higher for older age groups. As a result, crude death rates tend to be higher in populations with a larger proportion of older persons, and lower in populations with a larger proportion of younger persons.

An age-adjusted rate is a summary measure that may be used to compare mortality or disease risk in two populations with with different age compositions.

Back to Top


Deciding Which Measure to Use



So, how do I know which one to use !? You will want to use the measure that best informs the question you are trying to answer. This is a guideline, not a hard and fast rule, but generally:

If your question is: Then use:
MAGNITUDE: How big is the problem? Number of events (count)
PROBABILITY: What is the underlying risk in my population? Crude rate and confidence interval
DISPARITY: Is there a difference in risk after controlling for age? Age-adjusted rate and confidence interval


Back to Top


Go to the page on age-adjusted rates for health events.



Please feel free to contact us if you have questions, or suggestions for additions or improvements to this web page or the MT-IBIS website.

The information provided above is from the Office of Epidemiology and Scientifict Support, Montana Department of Public Health and Human Services MT-IBIS web site (http://dphhs.mt.gov/). The information published on this website may be reproduced without permission. Please use the following citation: " Retrieved Sun, 15 December 2019 4:08:04 from Office of Epidemiology and Scientific Support, Montana Department of Public Health and Human Services, Indicator-Based Public Healt Information System for Public Health Web site: http://dphhs.mt.gov/ ".

Content updated: Mon, 23 May 2016 12:17:20 MDT